set_serial

set_serial_param ( : : SerialHandle, BaudRate, DataBits, FlowControl, Parity, StopBits, TotalTimeOut, InterCharTimeOut : )

Set the parameters of a serial device.

set_serial_param can be used to set the parameters of a serial device. The parameter BaudRate determines the input and output speed of the device. It should be noted that not all devices support all possible speeds. The number of sent and received data bits is set with DataBits. The parameter FlowControl determines if and what kind of data flow control should be used. In the latter case, a choice between software control ('xon_xoff') and hardware control ('cts_rts', 'dtr_dsr') can be made. If and what kind of parity check of the transmitted data should be performed can be determined by Parity. The number of stop bits sent is set with StopBits. Finally, two timeout for reading from the serial device can be set. The parameter TotalTimeOut determines the maximum time, which may pass in read_serial until the first character arrives, independent of the actual number of characters requested. The parameter InterCharTimeOut determines the time which may pass between the reading of individual characters, if multiple characters are requested with read_serial. If one of the timeouts is set to -1, a read waits an arbitrary amount of time for the arrival of characters. Thus, on Windows NT systems, a total timeout of TotalTimeOut + n InterCharTimeOut results if n characters are to be read. On Unix systems, only one of the two timeouts can be set. Thus, if both timeouts are passed larger than -1, only the total timeout is used. The unit of both timeouts is milliseconds. For each parameter, the current values can be left in effect by passing 'unchanged'.

Parameters

`SerialHandle` (input_control)	serial_id `->` integer
Serial interface handle.

`BaudRate` (input_control)	integer `->` integer / string
Speed of the serial interface.
Default value: 'unchanged'
List of values: 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800, 9600, 19200, 38400, 57600, 76800, 115200, 153600, 230400, 307200, 460800, 'unchanged'

`DataBits` (input_control)	integer `->` integer / string
Number of data bits of the serial interface.
Default value: 'unchanged'
List of values: 5, 6, 7, 8, 'unchanged'

`FlowControl` (input_control)	string `->` string
Type of flow control of the serial interface.
Default value: 'unchanged'
List of values: 'none', 'xon_xoff', 'cts_rts', 'dtr_dsr', 'unchanged'

`Parity` (input_control)	string `->` string
Parity of the serial interface.
Default value: 'unchanged'
List of values: 'none', 'odd', 'even', 'unchanged'

`StopBits` (input_control)	integer `->` integer / string
Number of stop bits of the serial interface.
Default value: 'unchanged'
List of values: 1, 2, 'unchanged'

`TotalTimeOut` (input_control)	integer `->` integer / string
Total timeout of the serial interface in ms.
Default value: 'unchanged'
Suggested values: -1, 0, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 'unchanged'

`InterCharTimeOut` (input_control)	integer `->` integer / string
Inter-character timeout of the serial interface in ms.
Default value: 'unchanged'
Suggested values: -1, 0, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 'unchanged'

Result

If the parameters are correct and the parameters of the device could be set, the operator set_serial_param returns the value 2 (H_MSG_TRUE). Otherwise an exception is raised.

Parallelization Information

set_serial_param is reentrant and processed without parallelization.

Possible Predecessors

open_serial, get_serial_param

Possible Successors

read_serial, write_serial

See also

get_serial_param

Module

System